Date：2022-02-22 15:47:10

First, what is aging test? During the aging test, the components on the special aging circuit board will bear the pressure equal to or higher than its rated working conditions to eliminate any components that fail prematurely before the rated life. These test conditions include temperature, voltage / current, operating frequency or any other test conditions specified as the upper limit. These types of stress tests are sometimes referred to as accelerated life tests (a subset of halt / HASS) because they simulate the operation of components under extreme conditions for a long time. View >>

Date：2022-02-22 15:32:17

What is UV testing? UV test, also known as UV aging test, is a process of simulating various factors involved in the actual use conditions of products and strengthening the experiment of corresponding conditions. It can reproduce the damage caused by sunlight, rain and dew and obtain the service life of products in a short time. The equipment carries out the test by exposing the material to be tested to the controlled interactive cycle of sunlight and moisture and increasing the temperature at the same time. View >>

Date：2022-02-21 14:29:00

Nondestructive testing is to use the acoustic, optical, magnetic and electrical characteristics of materials to detect whether there are defects or non-uniformity in the tested object without damaging or affecting the service performance of the tested object, and give information such as the size, location, nature and quantity of defects. With the continuous improvement of testing requirements, nondestructive testing technology has widely adopted digital technology and has gradually entered the measurement field. For example, for the measurement of geometric quantities and material characteristic parameters, it is necessary to monitor and control the continuous stability of instrument indexes according to certain procedures, so as to improve the reliability of testing results. View >>

Date：2022-02-21 14:00:00

IC chip appearance detection system in the production process of IC integrated chip devices, the appearance quality detection of the chip is an essential link, including the detection items such as pin size, deformity, deflection, uneven spacing and poor flatness of the chip, and the above quality problems will directly affect the quality of circuit products. The automatic detection of appearance defects requires the use of electronic component appearance detection equipment. Then, how to detect the appearance defects of electronic components? View >>

Date：2022-02-21 13:39:29

Low temperature test is mainly used to evaluate the impact of low temperature conditions on the safety, integrity and performance of equipment during storage, work and disassembly. To determine the sequence of low temperature test, two principles should be followed: maximize the service life of equipment and the applied environment should be able to display the superposition effect to the greatest extent. View >>

Date：2022-02-21 13:25:02

Ultrasonic testing, also known as ultrasonic testing and ultrasonic flaw detection, is a kind of nondestructive testing. Nondestructive testing is a testing method to check the surface and internal quality of the inspected parts without damaging the working state of the workpiece or raw materials. Ultrasonic nondestructive testing (NDI) is a development and application of ultrasonic nondestructive testing. Its equipment includes: ultrasonic flaw detector, probe, coupling agent and standard test block. Its purpose is to detect casting shrinkage cavity, bubble, welding crack, slag inclusion, incomplete fusion, incomplete penetration and other defects and thickness measurement. View >>

Date：2022-02-18 16:23:00

Chemical analysis is classified into classical gravimetric analysis and volumetric analysis. Gravimetric analysis refers to the calculation of the chemical composition of the sample according to the mass of the product generated by the chemical experimental reaction of the sample. Most of them refer to the mass method. Volumetric method refers to the volume of standard test solution consumed by the sample in the reaction. The volumetric method can determine the main components of the sample and the secondary components of the sample. View >>

Date：2022-02-18 16:20:00

Alternating damp heat test includes constant damp heat test and alternating damp heat test. The test simulates the environment of tropical rain forest to determine the adaptability of products and materials to use and storage when temperature changes and product surface condensation. It is commonly used in life test, evaluation test and comprehensive test. The technical indexes include: temperature, relative humidity, conversion time and alternating times. View >>

Date：2022-02-18 16:00:00

Component analysis technology is mainly used to analyze unknown substances and unknown components. Through component analysis technology, you can quickly determine the various components in the target sample, help you conduct qualitative and quantitative analysis on the sample, and identify the materials, raw materials, additives, specific components and contents, foreign matters, etc. of polymer materials such as rubber. View >>

Date：2022-02-17 18:08:31

Inspection is the conformity evaluation of electronic products through observation and judgment, combined with measurement and trial test when appropriate. Product inspection is an essential means of quality control in the production of modern electronic enterprises. It mainly plays the role of process control, quality control and judging the qualification of products. The product inspection shall implement the "three inspection" system combining self inspection, mutual inspection and full-time inspection. View >>